GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
TE: 89670
no sdio debug board detected

BL2 Built : 13:55:05, Jan 28 2016.
gxb g3625dd5 - xiaobo.gu@droid05

Board ID = 1
set vcck to 1100 mv
set vddee to 1000 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same
DDR0: 1024MB(auto) @ 912MHz(2T)-13
DataBus test pass!
AddrBus test pass!
Load fip header from eMMC, src: 0x0000c000, des: 0x01400000, size: 0x00004000
Load bl30 from eMMC, src: 0x00010000, des: 0x01000000, size: 0x0000a9b0
Sending bl30...........................................OK.
Run bl30...
Load bl301 from eMMC, src: 0x0001c000, des: 0x01000000, size: 0x00001c50
Wait bl30...Done
Sending bl301........OK.
Run bl301...
, src: 0x00020000, des: 0x10100000, size: 0x00012130


--- UART initialized after reboot ---
[Reset cause: unknown]
[Image: unknown, amlogic_v1.1.3054-53e549c 2016-03-31 20:40:25 xing.xu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef Load bl32 from eMMC, src: 0x00034000, des: 0x05300000, size: 0x00088720
be ad de not ES chip
efuse init ops = 13
efuse init hdcp = c, cf9=7
[0.216216 Inits done]
secure task start!
high task start!
low task start!
Load bl33 from eMMC, src: 0x000c0000, des: 0x01000000, size: 0x000a04a0
NOTICE:  BL3-1: v1.0(debug):15009cf
NOTICE:  BL3-1: Built : 11:26:34, Dec 23 2015
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Initializing BL3-2
INF TEE-CORE:show_version_info:68:
ATOS-1.2(gxbb@) (gcc 4.7.3) (Mar 09 2016-10:19:03)

WARNING: Unimplemented Sip Call: 0x82000045
WARNING: Unimplemented Sip Call: 0x82000044
INF TEE-CORE:init_teecore:77: teecore inits done
INF TEE-CORE:main_init:144: ATOS initialize finished
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01 (Aug 01 2016 - 14:20:25)

DRAM:  1 GiB
Relocation Offset is: 36ed3000
register usb cfg[0][1] = 0000000037f62860
register usb cfg[0][2] = 0000000037f62880
register usb cfg[2][0] = 0000000037f628a0
vpu detect type: 5
vpu clk_level = 7
set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=8, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000033ec3770
aml_priv->desc_buf = 0x0000000033ec5900
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000033ec7ff0,dt_addr=0000000033ec7ff0
parts: 11
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06: instaboot   0000000020000000 1
07:      boot   0000000002000000 1
08:    system   0000000040000000 1
09:     cache   0000000020000000 2
10:      data   ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                     2400000           4000000                  0
   2: cache                        6c00000          20000000                  2
   3: env                         27400000            800000                  0
   4: logo                        28400000           2000000                  1
   5: recovery                    2ac00000           2000000                  1
   6: rsv                         2d400000            800000                  1
   7: tee                         2e400000            800000                  1
   8: crypt                       2f400000           2000000                  1
   9: misc                        31c00000           2000000                  1
  10: instaboot                   34400000          20000000                  1
  11: boot                        54c00000           2000000                  1
  12: system                      57400000          40000000                  1
  13: data                        97c00000         13a400000                  4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
      Amlogic multi-dtb tool
      Single dtb detected
Net:   Meson_Ethernet
iubootVersion  = 2,pubootVersion = 2
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
ret = 1 .[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 74
OEM: 4a60
Name: USDU1
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 4-bit
reading kernel.img
** Unable to read file kernel.img **
hpd_state=1
[CANVAS]addr=0x3f800000 width=3840, height=2160

[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc800023d
config HPLL done
set_hpll_od3_clk_div[216] div = 6
j = 8  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
enc_vpu_bridge_reset[977]
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L504:key[deviceid] not programed yet
gpio: pin GPIOAO_3 (gpio 122) value is 1
saradc - saradc sub-system

Usage:
saradc saradc open <channel>            - open a SARADC channel
saradc close    - close the SARADC
saradc getval   - get the value in current channel
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel

Enter USB burn
Try connect time out 701, 700, 1219
Device: SDIO Port B
Manufacturer ID: 74
OEM: 4a60
Name: USDU1
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 4-bit
reading kernel.img
** Unable to read file kernel.img **
Hit any key to stop autoboot:  0
Device: SDIO Port B
Manufacturer ID: 74
OEM: 4a60
Name: USDU1
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 4-bit
reading s905_autoscript
823 bytes read in 4 ms (200.2 KiB/s)
## Executing script at 01020000
########## cmd=if fatload mmc 0 0x1000000 u-boot.ext; then go 0x1000000; fi;
if fatload usb 0 0x1000000 u-boot.ext; then go 0x1000000; fi;
setenv env_addr 0x1040000
setenv boot_start 'bootm ${loadaddr} - ${dtb_mem_addr}'
setenv addmac 'if printenv mac; then setenv bootargs ${bootargs} mac=${mac}; elif printenv eth_mac; then setenv bootargs ${bootargs} mac=${eth_mac}; fi'
setenv try_boot_start 'if fatload ${devtype} ${devnum} ${loadaddr} KERNEL; then fatload ${devtype} ${devnum} ${env_addr} uEnv.ini && env import -t ${env_addr} ${filesize} && run addmac; fatload ${devtype} ${devnum} ${dtb_mem_addr} ${dtb_name} && run boot_start; fi'
setenv devtype mmc
setenv devnum 0
run try_boot_start
setenv devtype usb
for devnum in 0 1 2 3 ; do run try_boot_start ; done

reading u-boot.ext
** Unable to read file u-boot.ext **
** Bad device usb 0 **
reading KERNEL
26948674 bytes read in 1232 ms (20.9 MiB/s)
reading uEnv.ini
191 bytes read in 2 ms (92.8 KiB/s)
mac=E8:18:63:51:56:4A
reading /amlogic/meson-gxbb-wetek-hub.dtb
38560 bytes read in 8 ms (4.6 MiB/s)
ee_gate_off ...
## Booting kernel from Legacy Image at 01080000 ...
   Image Name:
   Image Type:   AArch64 Linux Kernel Image (lzo compressed)
   Data Size:    26948610 Bytes = 25.7 MiB
   Load Address: 0aa00000
   Entry Point:  0aa00000
   Verifying Checksum ... OK
      Amlogic multi-dtb tool
      Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x0aa00000, end = 0x0e741008
   Loading Device Tree to 000000001fff3000, end 000000001ffff69f ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 4751554 us
[    0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma': size 896 MiB
[    0.261589] ==================================================================
[    0.261650] BUG: KASAN: global-out-of-bounds in __clk_register+0x1b60/0x2408
[    0.261694] Read of size 8 at addr ffff8000827df9e0 by task swapper/0/1
[    0.261719]
[    0.261737] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.19.0 #1 VOLUNTARY
[    0.261756] Hardware name: WeTek Hub (DT)
[    0.261764] Call trace:
[    0.261771]  show_stack+0x14/0x1c (C)
[    0.261792]  dump_stack_lvl+0x74/0x94
[    0.261811]  print_report+0x164/0x4b0
[    0.261828]  kasan_report+0x7c/0xbc
[    0.261847]  __asan_report_load8_noabort+0x1c/0x24
[    0.261865]  __clk_register+0x1b60/0x2408
[    0.261882]  devm_clk_hw_register+0x74/0x15c
[    0.261899]  meson_clkc_init+0xd4/0x20c
[    0.261917]  meson_clkc_syscon_probe+0x5c/0x94
[    0.261933]  platform_probe+0xbc/0x17c
[    0.261953]  really_probe+0x184/0x844
[    0.261969]  __driver_probe_device+0x154/0x35c
[    0.261985]  driver_probe_device+0x5c/0x184
[    0.262001]  __driver_attach+0x168/0x4a0
[    0.262017]  bus_for_each_dev+0xec/0x180
[    0.262032]  driver_attach+0x38/0x58
[    0.262047]  bus_add_driver+0x238/0x4c0
[    0.262062]  driver_register+0x150/0x388
[    0.262079]  __platform_driver_register+0x54/0x7c
[    0.262096]  gxbb_clkc_driver_init+0x18/0x20
[    0.262118]  do_one_initcall+0xb8/0x340
[    0.262136]  kernel_init_freeable+0x56c/0x61c
[    0.262155]  kernel_init+0x20/0x14c
[    0.262173]  ret_from_fork+0x10/0x20
[    0.262192]
[    0.262433] The buggy address belongs to the variable:
[    0.262451]  gxbb_32k_clk_parents+0x60/0x400
[    0.262480]
[    0.262495] The buggy address belongs to a vmalloc virtual mapping
[    0.262528] The buggy address belongs to the physical page:
[    0.262632]
[    0.262646] Memory state around the buggy address:
[    0.262667]  ffff8000827df880: 00 00 00 00 f9 f9 f9 f9 00 f9 f9 f9 f9 f9 f9 f9
[    0.262693]  ffff8000827df900: 00 04 f9 f9 f9 f9 f9 f9 00 04 f9 f9 f9 f9 f9 f9
[    0.262720] >ffff8000827df980: 00 00 00 00 00 00 00 00 00 00 00 00 f9 f9 f9 f9
[    0.262744]                                                        ^
[    0.262767]  ffff8000827dfa00: 00 01 f9 f9 f9 f9 f9 f9 00 06 f9 f9 f9 f9 f9 f9
[    0.262794]  ffff8000827dfa80: 00 00 02 f9 f9 f9 f9 f9 00 00 02 f9 f9 f9 f9 f9
[    0.262818] ==================================================================
LibreELEC:/ # uname -a
Linux LibreELEC 6.19.0 #1 SMP Mon Feb  9 05:19:47 UTC 2026 aarch64 GNU/Linux
LibreELEC:/ #
